Søgning i bogen
Den bedste måde at søge i bogen er ved at downloade PDF'en og søge i den.
Derved får du fremhævet ordene visuelt direkte på billedet af siden.
Digitaliseret bog
Bogens tekst er maskinlæst, så der kan være en del fejl og mangler.
Remarks.
the double strake below the
rivetted in the ordinary way.
Single rivetted.
The 14" strap is for Treble
Rivetting and 181/2 " for
Chain Rivetting, the rivets
through the frames are 7/s".
Double and single rivetted.
The 51/1" pitch in the Frame
|Butt Straps over every butt
I on the outside.
Butt Straps 11/16" by 171/2"
wide, chain rivetted.
This is double rivetted, except
|that every alternate rivet next
the ioot ofAngleIr. Is omitted.
Watertight Work.
11/4" Rivets are used to fasten
the garboard Strake to the
outside Flat Keel Plate as
well as tothe next strake out.
Single rivetted, the 8/16" Plate
and 41/2" Pitcli is for water-
tight work.
Single rivetted.
The 4/2" pitch is given to the
I rivets passing through the
j 5/8" & 9/16" plates, being
|watertight work.
Fortsat
Rivets.
Size | Pitch.
Breadth of Lap. i
Thickness of Irou.
Northumberland« fortsat.
Description of Work.
The pitch of livets in the edges is from 31/2 to 4 Diameters; the butts for 4 strakes out on each side of the keel
are treble
6"
the remainder of the butts of outside plating
Main Deck Ports and the sheer strake arc chain rivetted;
3/4
78
71/2" to 81/2" Edge Str.
Butt Straps14"-181/2
33/.
4" to 51/4
61/2" to 7"
41/2" to 9'
41/4" to 41/
7"
fl.
78"
to
to
to
to
to
61/2"
61/2"
61/2"
61/2"
5" to 41/2
6 "
to 61/
7a"
Lapped 81/4
31/2
s" & ’A »"Pl to5/8" Angle Ir.
5/a & 71»" Pl. to 11/16"
5/8" Strips
do
Two 9/16 " Pl
Id
Two
5/8" Pl. to 1/2" Angle Iron.
Two 5/8" Pl. to 3It" Angle Ir
/8 " Pl. to two Angle Irons
one 3/4 ", the other 9/16 "
11/8 " Pl. to 5/8" & 8/16 "
Angle Irons
1" Pl to 5/8" & 3/16" Angle Ir.
I7s" Pl. to 5/8" &3/16" Angle Ir.
13/16"Pl. to ä/8"&9/i6"Angle Ir.
3/4 Pl. to 5/8" & 3/16 Angle Ir.
/16 "Angle Ir to 7/16"&8/16"P1|
2" Ang Ir. to two’/s" Ang Ir.
191/
Plating behind Armour Pl. to the Frames
Edges of Plating.
op
Butts of
Edges of Double Strake under M D. Ports.
Edges of Sheer Strake.
Upper Deck Stringer to Beams.
Upper D. Str. Angle Iron to Sheer Strake.
Upper Deck Stringer Angle Iron to Stringer
also to Angle Iron round Top of Interm.
Frames & Stringer.
Bottom plating to single frame Angle Iron
on floors & transverse plates.
do.
do.
do.
do.
do.
do.
do
do.
or
Pg
Angle Iron to
Transverse plates
watertight and other Longit. Frames.
Continuous transverse frames to outside
double frame Angle Irons above armour
shelf
Continuous transverse frames to trans-
verse plates and floor plates below ar-
mour shelf.